User Preferences Parameters

Sets phone user preferences.

Table 1. User Preferences Parameters

Template

Parameter

Permitted Values

Change Causes

Restart or Reboot

features.cfg

up.25mm

Specifies whether to use a mobile phone or a PC to connect to the 2.5mm audio port on a conference phone.

1 (Default) - Mobile phone

2 - PC

No

features.cfg

up.accessibilityFeatures

Specifies whether to display accessibility features or not.

0 (Default) - Accessibility features are disabled.

1 - Screen background flashes orange for incoming calls.

For VVX 1500 only.

No

features.cfg

up.backlight.idleIntensity

Brightness of the LCD backlight when the phone is idle. Range is 0 to 3.

1 (Default) - Low

0

2 - Medium

3 - High

VVX 300/301/310/311 = 0, 1, 2, 3

All other phones = 1, 2, 3

If this setting is higher than active backlight brightness ( onIntensity ), the active backlight brightness is used.

No

features.cfg

up.backlight.onIntensity

Brightness of the LCD backlight when the phone is active (in use). Range is 0 to 3.

3 (Default) - High

1 - Low

2 - Medium

VVX 300/301/310/311 = 0, 1, 2, 3

All other phones = 1, 2, 3

No

features.cfg

up.backlight.timeout

Number of seconds to wait before the backlight dims from the active intensity to the idle intensity. Range is 5 to 60.

40 (default)

No

features.cfg

up.basicSettings.networkConfigEnabled

Specifies whether Network Configuration is shown or not shown under the Basic Settings menu.

0 (default) - Network Configuration is not shown under Basic Settings.

1 - Basic Settings menu shows Network Configuration with configurable network options for the user without administrator rights.

No

features.cfg up.DIDFormat

NumberAndExtension (default) – Display the DID number and extension.

NumberOnly – Display the DID number on the phone screen.

No

features.cfg

up.cfgWarningsEnabled

Specifies whether a warning displays on a phone or not.

0 (Default) - Warning does not display.

1 - Warning is displayed on the phone if it is configured with pre-UC Software 3.3.0 parameters.

No

em.cfg

up.em.linkalivecheck.enabled

Specifies whether a host VVX phone pings expansion modules or not.

0 (Default) - Host VVX phone does not ping the expansion modules.

1 - Host VVX phone periodically sends ping packets to the expansion modules.

No

features.cfg

up.handsetModeEnabled

Enable or disable the handset port.

1 (Default)

0

No

debug.cfg

up.headsetAlwaysUseIntrinsicRinger

1 (Default) - USB headset uses the intrinsic ringer mixed with DSP ringer when the sound effect destination is the USB headset.

0

No

features.cfg

up.headsetMode

Sets the preferred audio mode of handsfree or headset.

0 (Default) - Handsfree mode is used by default instead of the handset.

1 - Headset is used as the preferred audio mode after the headset key is pressed for the first time, until the headset key is pressed again.

No

features.cfg

up.hearingAidCompatibility.enabled

Specifies whether audio Rx equalization is enabled or disabled.

0 (Default) - Audio Rx equalization is enabled.

1 - Phone audio Rx (receive) equalization is disabled for hearing aid compatibility.

No

features.cfg

up.idleBrowser.enabled

Specifies if the idle browser is enabled or disabled.

0 (Default) - Idle browser is disabled.

1 - Idle browser is enabled.

If the parameter up.prioritizeBackgroundMenuItem.enabled is set to 1, displays the background or the idle browser on the phone menu.

No

features.cfg

up.idleStateView

Sets the phone default view.

0 (Default) - Call/line view is the default view.

1 - Home screen is the default view.

Yes

sip-interop.cfg

up.idleTimeout

Set the number of seconds that the phone is idle for before automatically leaving a menu and showing the idle display.

During a call, the phone returns to the Call screen after the idle timeout.

40 seconds (default)

0 to 65535 seconds

Yes

features.cfg

up.IdleViewPreferenceRemoteCalls

Determines when the phone displays the idle browser.

0 (Default) - Phone with only remote calls active, such as on a BLF monitored line, is treated as in the idle state and the idle browser displays.

1 - Phone with only remote calls active, such as on a BLF monitored line, is treated as in the active state and the idle browser does not display.

Yes

sip-interop.cfg

up.lineKeyCallTerminate

Specifies whether or not you can press the line key to end an active call.

0 (Default) - User cannot end an active call by pressing the line key.

1 - User can press a line key to end an active call.

No

sip-interop.cfg

up.numberFirstCID

Specifies what is displayed first on the Caller ID display.

0 (Default) - Caller ID display shows the caller's name first.

1 - Caller's phone number is shown first.

Yes

features.cfg

up.numOfDisplayColumns

Sets the maximum number of columns the VVX 500/501, 600/601, or Polycom Trio solution display. Set the maximum number of columns that phones display. Range is 0 to 4.

VVX 500/501 = 3 (Default)

VVX 600/601 = 4 (Default)

Polycom Trio=3 (Default)

0 - Phones display one column.

Yes

features.cfg

up.offHookAction.none

0 (Default)

1 - When the user lifts the handset, the phone does not seize the line and the ringer continues until the user takes further action.

Yes

features.cfg

up.OffHookIdleBrowserView.enabled

Specifies whether or not to display the idle browser on screen after the phone goes off hook.

0 (Default) - Idle browser does not display on screen after the phone goes off hook.

1 - Idle browser continues to display on screen after the phone goes off hook.

No

features.cfg

up.oneTouchDirectory

Displays the Address Book icon on the main menu and the Skype for Business Directory search option.

1 (Default)

0

No

features.cfg

up.osdIncomingCall.Enabled

Specifies whether or not to display full screen popup or OSD for incoming calls.

1 (Default) - Full screen popup or OSD for incoming calls displays.

0 - Full screen popup or OSD for incoming calls does not display.

No

sip-interop.cfg

up.prioritizeBackgroundMenuItem.enabled

User can choose whether or not the phone background should take priority over the idle browser.

1 (Default) - If up.idleBrowser.enabled is set to 1, this parameter can be set to 1 to display a Prioritize Background menu to the user.

Yes

site.cfg

up.ringer.minimumVolume

Configure the minimum ringer volume. This parameter defines how many volume steps are accessible below the maximum level by the user.

16 (Default) - Full 16 steps of volume range are accessible.

0 - Ring volume is not adjustable by the user and the phone uses maximum ring volume.

Example: Upon bootup, the volume is set to ½ the number of configured steps below the maximum (16). If the parameter is set to 8 on bootup, the ringer volume is set to 4 steps below maximum.

No

features.cfg

up.screenSaver.enabled

0 (Default) - Screen saver feature is disabled.

1 - Screen saver feature is enabled. If a USB flash drive containing images is connected to the phone, and the idle browser is not configured, a slide show cycles through the images from the USB flash drive when the screen saver feature is enabled.

The images must be stored in the directory on the flash drive specified by up.pictureFrame.folder. The screen saver displays when the phone has been in the idle state for the amount of time specified by up.screenSaver.waitTime.

No

features.cfg

up.screenSaver.type

Choose the type of screen saver to display.

0 (Default) - Phone screen saver displays default images.

2 - Phone screen saver displays the idle browser.

You can use this parameter with the VVX 300 and 400 series phones.

No

features.cfg

up.screenSaver.waitTime

Number of minutes that the phone waits in the idle state before the screen saver starts. Range is 1 to 9999 minutes.

15 (Default)

No

features.cfg

up.simplifiedSipCallInfo

0 (Default) -

1 - Displayed host name is trimmed for both incoming and outgoing calls and the protocol tag/information is not displayed for incoming and outgoing calls.

No

site.cfg

up.softkey.transferTypeOption.enabled

1 (default) -The user can change the transfer type from consultative to blind and vice versa using a soft key after the user has initiated a transfer, but before completing the call to the far end.

0 - There is no option to change from consultative to blind and blind to consultative when the user is in dial prompt after pressing the Transfer soft key.

No

features.cfg

up.status.message.flash.rate

Controls the scroll rate of the status bar on VVX 250, 350, and 450 business IP phones and 300 and 400 series business media phones. Range is 2 to 8 seconds.

2 seconds (Default)

No

features.cfg up.showDID

AllScreens (default) – Display the DID number on all the screens.

None – Disable DID number on phone.

LockedScreen – Display the DID number on the lock screen.

StatusScreen – Display the DID number on the Status screen/Idle screen.

IncomingOSD – Display the DID number on the incoming On Screen Display (OSD) screen.

LockedScreenIncomingOSD – Display the DID number on the lock and incoming OSD screen.

LockedAndStatusScreen – Display the DID number on the lock and Status/Idle screen.

StatusScreenIncomingOSD – Display the DID number on the incoming OSD and Status/Idle screen.

No

features.cfg

up.warningLevel

Line keys block display of the background image. All warnings are listed in the Warnings menu.

0 (Default) - The phone's warning icon and a pop-up message display on the phone for all warnings.

1 - Warning icon and pop-up messages are only shown for critical warnings.

2 - Phone displays a warning icon and no warning messages. For all the values, all warnings are listed in the Warnings menu.

Access to the Warnings menu varies by phone model:

VVX 1500 - Menu > Status > Diagnostics > Warnings

VVX phones - Settings > Status > Diagnostics > Warnings

Yes

features.cfg

up.welcomeSoundEnabled

1 (Default) - Welcome sound is enabled and played each time the phone reboots.

0 - Welcome sound is disabled.

To use a welcome sound you must enable the parameter up.welcomeSoundEnabled and specify a file in saf.x. The default UC Software welcome sound file is Welcome.wav.

Yes

features.cfg

up.welcomeSoundOnWarmBootEnabled

0 (Default) - Welcome sound is played when the phone powers on (cold boot), but not after it restarts or reboots (warm boot).

1 - Welcome sound plays each time the phone powers on, reboots, or restarts.

Yes

features.cfg up.display.showFullCallerID Phone displays the caller ID.

0 (default) – Phone displays the caller ID on the first line.

1 – Phone displays the caller ID on the second line.

No